Thursday, September 18, 2014

The clean up

This is the shit!!
Brasso is the best shit ever invented for cleaning metal surfaces. I have used this for years on my bike. After exposing the dirt fest that was the internals of the rear of my bike in yesterdays blog, a 10 minute session with the pressure cleaner and some brasso and good old elbow grease brought the rear section back to new stone chipped not so new.

Even with the pressure cleaner after 10 minutes nothing looked different. After rubbing in the brasso within a minute all was clean and shiny again. Thank you Brasso and you can send the cheque in the mail.


Now its time to get some riding in.




Wednesday, September 17, 2014

A Shocking Development

News has filtered through that Bobskoot had recently passed away. It's left the motoblogging community reeling as just about everybody in the blogging community knew Bob. May you now rest in peace Bob and ride long and hard where ever you now are.


It's been raining the last few weekends so I haven't been able to get out for a ride lately. I decided that it was finally time to unleash the moths from the dusty cobweb riddled thing I call a wallet and splurge on getting my rear shock rebuilt. I've only been talking about it for about 5 years now. Maybe with an up and at em attitude like that I could become a member of the West Coast Procrastinators.

I pulled the rear shock out which took about 5 minutes and on the advise of Stu who you saw in the last post I did, I took it down to Teknik Motorsport suspension specialists at Penrith for the rebuild. I met Nick the owner, who was knowledgeable and pretty fair with the pricing.  I also got them to put in a new spring as the original fitment spring is only weighted for a 69kg rider. I had always had the spring pre load turned up to 1 from hardest and it was still too soft. It's never been any good really. The shock bump rubber at the base of the spring has crumbled into dust and is also in need of replacement.

One well past its used by date R1 rear shock

Here's the shock back with the new spring and bump rubber installed. My massive girth required a spring that could launch a shuttle into space once compressed. They re-valved the shock as well as Nick said if they didn't the rebound would send me over the moon. I didn't want to take him up on that offer so I duly had them do the re-valving. I can't afford the trip into space let alone the moon.

One rebuilt R1 shock complete with new spring and bump rubber




Compression Damping screw with
pre-load below that


Here it is fitted back into the bike, it wasn't to difficult at all really. I reset all of the pre-load, rebound damping and compression damping back to factory settings.

Then I adjusted them harder by 1 notch each. I'll give that a shot for a starting point and adjust from there. It has to be much better than when it was new.

The pic on the right shows the Compression damping screww at top with the blue ring and under neath the preload is set to 5. 4 is factory standard setting. Now just to set up the sag again with the new shock.

Below is the rebound damping screw also circled in blue.


Rebound damping screw



During the works I also pulled out the rear hugger just for some better access. What I discovered was a little disturbing. On the left hand side of the swing arm where the plastic bolted to the aluminium bracing arm the plastic had rubbed it's way into the metal. There is a pretty deep groove there at about 1mm deep. See picture below. Pulling all this stuff apart has just shown me that there is a lot more cleaning to be done. I guess there nearly 15 years of dirt, mud, clay and crap under there. 

Is Plastic mightier than aluminium? You be the judge.


Anyone got a hose?






I hadn't finished there either, as I had some bling arrive in the post yesterday that needed installing. I had broken one of the plastic windscreen bolts when I did the fluid change last month. They are really cheap plastic screws so I ordered some new ones from the interwebs. Shiney new blue anodised aluminium bolts.





And to go with that some new bar end weights to replace the stone chipped rusty original bar weights. And not just any bar weights R1 bar weights. She's all blinged up now.













Tuesday, September 2, 2014

The pointy end of the field

Here's a good friend of ours here at the Road to Nowhere who occasionally shows up on these pages getting down to business and showing us how its done at Wakefield park last weekend at the post classic racing. Thanks for the pics Rick.




Hope every things all right mate and it wasn't too costly for you.